brushless motors LiPo batteries electronic speed controllers inrunner Motors outrunner motors Spektrum Transmitters and Receivers servos

The Fixed Wing
Electric Flight Specialists

<<<  Back
Tel: 01256 782 512
Email us 
Click here to Check us out on Facebook and to get access to special offers and notifications of new releases

E-Flite Convergence VTOL BNF Basic (EFL11050)

EFL11050 E-Flite Convergence VTOL BNF Basic

EFL11050 E-Flite Convergence VTOL BNF Basic

EFL11050 E-Flite Convergence VTOL BNF Basic

EFL11050 E-Flite Convergence VTOL BNF Basic


Share on your Facebook Page

E-Flite Convergence VTOL BNF Basic EFL11050 - VTOL

Vertical Take Off and Landing

VTOL (Vertical Takeoff and Landing) RC models are usually a mixed bag when it comes to performance. If they are stable, their speed and agility is often lackluster. If they are nimble, pilots have to work harder to transition between hovering and airplane flight. The Convergence™ VTOL park flyer changes all that. Its unique design and exclusive flight control software give you the best of both agility and stability while making the transition between multirotor and airplane flight so smooth and predictable, you will feel right at home your first time on the sticks.

Sleek and Simple

Unlike complex VTOL aircraft that rotate the entire wing and require as many as four motors to achieve vertical and forward flight, the Convergence park flyer uses a simple, yet sleek, delta-wing design with three brushless motors – two rotating motors on the wing and a fixed-position motor in the tail.

In multirotor flight the wing-mounted motors rotate up into the vertical position to provide lift and flight control along with the motor in the tail. In airplane flight, the wing-mounted motors rotate down into the horizontal position and the model’s elevons take over pitch and bank control. Yaw control in airplane flight is provided by differential thrust from the wing-mounted motors.

Automated Transition

Making the transition between multirotor and airplane flight is as simple as flipping a switch. The flight controller will smoothly rotate the two wing-mounted motors into the correct flight attitude and activate the rear motor as needed.

Stability and Acro Flight Modes

These two flight modes give you a wide range of performance for every phase of flight.

Stability Mode

In multirotor flight, Stability Mode will limit pitch and bank angles and work to keep the model level when you release the sticks. This allows you to take off and land like a pro, even if you’ve never flown a multirotor before. In airplane flight, it will limit pitch and bank angles and automatically return the wings to level when the sticks are released.

Acro Mode

In Acro Mode there are no angle limits or self-leveling in any phase of flight. During multirotor flight, the model will behave like a conventional multirotor that pitches and banks in whatever direction you want it to fly. It can flip and roll like other multirotors, too.

FPV Ready

The model is designed to accommodate several of the most popular FPV camera systems. There is a camera bay under the nose and a place to mount the video transmitter in the rear of the aircraft. Both locations are easy to access so installation takes just a few minutes.

Super-Simple Transmitter Setup

This Bind-N-Fly® version can be flown with any full-range, 6+ channel DSMX®/DSM2® aircraft transmitter and comes equipped with a Spektrum serial receiver that is connected to the flight controller. No complex transmitter setup or programming is required. You use your “GEAR” switch for selecting Stability or Acro mode and your “AUX 1” switch to transition between multirotor and airplane flight.


  • Multirotor versatility and sport plane agility
  • Designed by champion pilot, Mike McConville
  • Exclusive flight control software makes it incredibly easy to fly
  • Stability and Acro Modes provide a wide performance envelope
  • Powerful brushless motors for outstanding speed and climb performance (Included)
  • Super-simple transmitter setup with no complex programming required
  • FPV-ready with camera and video transmitter mounting stations

Needed to Complete

What's in The Box

  • Convergence™VTOL BNF (Including Spektrum Reciever, Motors, ESC's, Props and Servos)
  • User Manual




Wingspan 650mm (25.6")
Length 680mm (26.9")
Battery 3S LiPo. 2200mAh - 3300mAh (3S 2200mAh 40C Recommended)
Flying Weight Approx 771g (1.7lbs)

Please Note: Due to size and weight limitations we are unable to ship kits outside of the UK


Please Note Due to having our knuckles severely rapped by the Post Office we can no longer send any kind of battery via the post. Any order containing batteries will have to be sent via courier and this will incur a minimum of a £9.49 delivery and packaging charge.
We can not deliver batteries outside of mainland UK


Part Number Description Price Qty
BNF Basic
E-Flite Convergence VTOL BNF Basic
(RRP £274.99)
£247.49 Out of Stock
PPL-40C3S-2200 LiPo Battery 40C, 3S, 11.1V, 2200mAh £19.99
PPL-40C3S-2600 LiPo Battery 40C, 3S, 11.1V, 2600mAh £25.99
PPL-40C3S-3300 LiPo Battery 40C, 3S, 11.1V, 3300mAh £32.99

<<<  Back Top